Fife糾偏-檢驗,MAGPOWR張力-控制,Tidland分切-卷取,MAXCESS國際集團,美塞斯產品,美塞斯中國,授權代理商廈門飛美泰貿易有限公司 Fife糾偏-檢驗,MAGPOWR張力-控制,Tidland分切-卷取,MAXCESS國際集團,美塞斯產品,美塞斯中國
首 頁 公司介紹 行業方案 產品信息 服務和支持 熱點新聞 招聘信息 留言板 聯系我們



美塞斯產品家族 當前位置:首頁 >> MAGPOWR產品首頁 >> TS Series 

TS Load Cells

TS Load CellsThe MAGPOWR TS line of  load cells are extremely accurate devices used to measure tension in any unwind, rewind, or intermediate web processing application. The unique low profile design minimizes space requirements inside the machine frames, thus maximizing the potential for web width. TS load cells also offer the flexibility of a variety of mounting styles and coupling options.

They are ruggedly constructed with mechanical overload stops in both force directions to eliminate sensor damage and the need to recalibrate even after extreme overloads. A full Wheatstone bridge arrangement of four foil strain gages is used in each sensor for the most accurate means of measuring web tension, reguardless of temperature change. In addition, all sensors incorporate a dual beam construction design to insure linear output under all loading conditions.

Key Features

  • Low profile design allows maximum web widths
  • Multiple mounting options for maximum flexibility
  • Three coupling styles for use with any type idler roll
  • Ruggedly constructed for long life and dependability
  • Mechanical overload stops for protection even under severe overloads
  • Full Wheatstone bridge design for measurement accuracy
  • Inch and Metric models for international installations
Load cell mounting styles available
  • Stud Mount Load Cell
  • Pillow Block Load Cell
  • Flange Mount Load Cell

Split coupling models

Load Cells with Split Couplings can be used to measure web tension through dead-shaft or live-shaft idler rolls. With one load cell mounted to each side of the machine frame, the idler roll is supported between the two load cells. The resultant force of the web tension is measured as a load on the roll by the load cells.

The Split Coupling allows the idler roll to be easily installed after the load cells have been mounted to the machine frames. The coupling design also accommodates misalignment between the machine frames and allows for thermal expansion of the idler roll shaft during machine operation.

The unique coupling design also allows its use in both dead-shaft and live-shaft applications. As it is shipped from the factory, the coupling is configured to accommodate a dead-shaft installation.

In-roll coupling models

The In-Roll Coupling is designed to insert directly into the end of an idler roll. With one load cell mounted to each side of the machine frame, the idler roll is supported between the two load cells. The resultant force of the web tension is measured as a load on the roll by the load cells.

The In-Roll Coupling includes a spherical bearing to allow for smooth rotation of the idler roll and to accommodate misalignment between the machine frames. This coupling type eliminates the need for idler rolls with shafts and bearings, thus reducing the overall cost of the tension sensing system.

Wire pulley models

The Wire Pulley is used for single strand applications for any kind of material. When mounted to the side of a machine frame or bracket, a load cell measures tension in the strand as it passes over the nickel plated aluminum load cell pulley.

General Specifications:

Drift Resistance:
.02 degree C (versus competitive load cells at .02 degree F)

Gage Resistance:  350 ohms nominal

Excitation Voltage:  10 VDC nominal

[返回上一頁]  [返回MAGPOWR產品主頁]
版權所有© 2006-2013 廈門飛美泰自動化科技有限公司 地址:廈門市廈門火炬高新區火炬東路11號創業大廈711單元 郵編:361009
電話: (86)592-2107107 2051408 傳真: (86)592-2107108 Email: [email protected] 網址:http://www.rbnffn.tw
建議分辨率1024X768,IE6.0以上瀏覽器,以獲得最佳效果。閩ICP備09031839號 技術支持:澤迅網絡