Fife糾偏-檢驗,MAGPOWR張力-控制,Tidland分切-卷取,MAXCESS國際集團,美塞斯產品,美塞斯中國,授權代理商廈門飛美泰貿易有限公司 Fife糾偏-檢驗,MAGPOWR張力-控制,Tidland分切-卷取,MAXCESS國際集團,美塞斯產品,美塞斯中國
首 頁 公司介紹 行業方案 產品信息 服務和支持 熱點新聞 招聘信息 留言板 聯系我們



美塞斯產品家族 當前位置:首頁 >> Tidland產品首頁 >> Mark II Roll Saver 
Mark II Roll Saver

Mark II Roll Saver
Save your crushed core with Tidland's Mark I or Mark II Roll Savers. These roll savers are designed to re-open crushed cores, allowing for shaft insertion on rolls that would otherwise be considered scrap material. Ideal for mills and converters, Roll Savers provide fast results, and can be used virtually anywhere, without any special training.

The Roll Saver provides a return on your investment with its very first use. The cost of a Roll Saver is comparable to that of a damaged roll, creating a positive impact on profit margins and warehouse space. Air shafts cannot be inserted into rolls with even with the slightest deformation, leaving damaged rolls useless. With a Tidland portable hydraulic Roll Saver, rolls with core I.D.'s of 3" (76 mm) can be salvaged, providing a positive impact on warehouse space and an immediate return on investment.

The Mark II Roll Saver has a hydraulic pump located below the handle, transmitting up to 9,000 psi (621 bar) to the cast steel jaws. The closed jaws are positioned in the crushed roll. A few strokes on the pump handle will force the jaws open. To close the jaws, simply open the release valve. Repeating this process several times allows the Roll Saver to move further into the roll. Once inside the roll, the operator must rotate the Roll Saver to push out in all directions, especially in the direction of the maximum crush. The Mark II is designed for fiber cores and is not recommended for steel or steel tipped cores. Film rolls constricted or crushed by film tension may not be repairable.

Key Features:

  • Fully transportable - Lightweight design can be used virtually anywhere
  • Trouble-free Operation - Easy to operate hydraulics provide up to 4 tons of thrust, giving you fast results
  • Restores 3" (76 mm) cores
  • Cost effective - Return on your investment can occur with your first salvaged roll!
  • Easy to use

General Specifications:

  • Core ID:
    3" (76 mm)
  • Penetration:
    Maximum 10" (250 mm)
    Maximum Weight:
    19 lbs. (9kg)
  • Hydraulic Pressure:
    9,000 psi (621 bar)
    (Hydraulic ram located between jaws develops a thrust of 4 tons)
  • Expansion:
    Recommended for 45" (1025 mm) diameter rolls up to 36" (902 mm) wide

General Specifications:

Product Name: 

Mark II Roll Saver

Standard Unit:

For 3" (76 mm) cores

[返回上一頁]  [返回Tidland產品主頁]
版權所有© 2006-2013 廈門飛美泰自動化科技有限公司 地址:廈門市廈門火炬高新區火炬東路11號創業大廈711單元 郵編:361009
電話: (86)592-2107107 2051408 傳真: (86)592-2107108 Email: [email protected] 網址:http://www.rbnffn.tw
建議分辨率1024X768,IE6.0以上瀏覽器,以獲得最佳效果。閩ICP備09031839號 技術支持:澤迅網絡